APRS Track Direct

My position About ☰

reset

TA2IK-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TA2IK-11. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	RxTraffic*	TxTraffic*	RxDrop*	RSSI*	Voltage*
1731565843	64 Pkt	13 Pkt	4 Pkt	-59 dBm	0.08 V
1731564925	96 Pkt	16 Pkt	3 Pkt	-58 dBm	0.08 V
1731564005	94 Pkt	16 Pkt	4 Pkt	-59 dBm	0.08 V
1731563082	55 Pkt	17 Pkt	4 Pkt	-59 dBm	0.08 V
1731562164	57 Pkt	17 Pkt	5 Pkt	-58 dBm	0.08 V
1731561246	84 Pkt	17 Pkt	4 Pkt	-67 dBm	0.08 V
1731560326	90 Pkt	14 Pkt	4 Pkt	-67 dBm	0.08 V
1731559405	111 Pkt	16 Pkt	6 Pkt	-67 dBm	0.08 V
1731558481	79 Pkt	17 Pkt	4 Pkt	-67 dBm	0.08 V
1731557561	103 Pkt	19 Pkt	4 Pkt	-67 dBm	0.08 V
1731556638	87 Pkt	17 Pkt	3 Pkt	-66 dBm	0.08 V
1731555717	69 Pkt	14 Pkt	6 Pkt	-67 dBm	0.08 V
1731554798	49 Pkt	16 Pkt	2 Pkt	-67 dBm	0.08 V
1731553880	64 Pkt	17 Pkt	0 Pkt	-68 dBm	0.08 V
1731552961	88 Pkt	17 Pkt	0 Pkt	-66 dBm	0.08 V
1731552041	65 Pkt	16 Pkt	0 Pkt	-66 dBm	0.08 V
1731551121	80 Pkt	16 Pkt	0 Pkt	-67 dBm	0.08 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)