APRS Track Direct

My position About ☰

reset

E74BYZ-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object E74BYZ-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	V1*	V2*	I1*	I2*	Temp*
1790655672	57 V	56 V	132 A	127 A	128 C
1790655372	43 V	27 V	132 A	127 A	128 C
1790655072	17 V	9 V	132 A	127 A	128 C
1790654772	7 V	3 V	131 A	127 A	128 C
1790654472	3 V	1 V	131 A	127 A	128 C
1790654174	2 V	0 V	131 A	127 A	128 C
1790653872	1 V	0 V	132 A	127 A	128 C
1790653573	1 V	0 V	132 A	127 A	128 C
1790653272	1 V	0 V	132 A	127 A	128 C
1790652972	1 V	0 V	131 A	127 A	128 C
1790652672	1 V	0 V	132 A	127 A	128 C
1790652372	1 V	0 V	131 A	127 A	128 C
1790652072	1 V	0 V	132 A	127 A	128 C
1790651772	1 V	0 V	131 A	127 A	128 C
1790651472	1 V	0 V	131 A	127 A	128 C
1790651172	1 V	0 V	132 A	127 A	128 C
1790650873	1 V	0 V	132 A	127 A	128 C
1790650572	1 V	0 V	131 A	127 A	128 C
1790650272	1 V	0 V	132 A	127 A	128 C
1790649972	1 V	0 V	131 A	127 A	128 C
1790649672	1 V	0 V	132 A	127 A	128 C
1790649372	1 V	0 V	132 A	127 A	128 C
1790649072	1 V	0 V	131 A	127 A	128 C
1790648772	1 V	0 V	132 A	127 A	128 C
1790648472	1 V	0 V	131 A	127 A	128 C

*Used Equation Coefficients:

V1: 0, 1, 0

V2: 0, 1, 0

I1: 0, 1, 0

I2: 0, 1, 0

Temp: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)