APRS Track Direct

My position About ☰

reset

HS4KGC-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS4KGC-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	TxTraffic*	RSSI*	Voltage*
1732528345	0 Pkt	-42 dBm	15.07 V
1732527718	0 Pkt	-40 dBm	15.11 V
1732527093	0 Pkt	-42 dBm	15.11 V
1732526468	1 Pkt	-36 dBm	15.05 V
1732525841	0 Pkt	-38 dBm	15.11 V
1732525216	0 Pkt	-39 dBm	15.11 V
1732524589	0 Pkt	-35 dBm	15.09 V
1732523964	1 Pkt	-36 dBm	15.09 V
1732523338	1 Pkt	-37 dBm	15.11 V
1732522712	0 Pkt	-37 dBm	15.09 V
1732522087	0 Pkt	-39 dBm	15.09 V
1732521461	0 Pkt	-33 dBm	15.11 V
1732520836	0 Pkt	-33 dBm	15.11 V
1732520211	0 Pkt	-32 dBm	15.09 V
1732519586	0 Pkt	-34 dBm	15.09 V
1732518961	0 Pkt	-34 dBm	15.09 V
1732518335	0 Pkt	-33 dBm	15.09 V
1732517710	0 Pkt	-33 dBm	15.11 V
1732517085	0 Pkt	-32 dBm	15.09 V
1732516460	0 Pkt	-33 dBm	15.09 V
1732515835	0 Pkt	-37 dBm	15.09 V
1732515209	0 Pkt	-36 dBm	15.09 V
1732514584	0 Pkt	-35 dBm	15.11 V
1732513959	0 Pkt	-37 dBm	15.11 V
1732513334	0 Pkt	-37 dBm	15.09 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)