APRS Track Direct

My position About ☰

reset

BM6HIP-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BM6HIP-13. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1749329606	27.1 C	40 p	154 p	3002 p
1749328405	26.6 C	68 p	155 p	2999 p
1749327205	27.5 C	46 p	135 p	2970 p
1749326005	27.5 C	41 p	137 p	2961 p
1749324805	26.6 C	48 p	140 p	2954 p
1749323605	27 C	48 p	135 p	2946 p
1749322406	27.9 C	43 p	135 p	2944 p
1749321206	27.6 C	43 p	146 p	2940 p
1749320006	28.2 C	49 p	157 p	2934 p
1749318806	28.1 C	53 p	149 p	2924 p
1749317605	27.4 C	55 p	139 p	2906 p
1749316405	26.9 C	41 p	143 p	2888 p
1749315205	27.9 C	43 p	142 p	2887 p
1749314005	28.1 C	59 p	149 p	2884 p
1749312805	27.6 C	40 p	162 p	2861 p
1749311605	28.2 C	50 p	174 p	2860 p
1749310405	27.6 C	72 p	168 p	2847 p
1749309205	27.1 C	52 p	143 p	2813 p
1749308005	28.2 C	44 p	140 p	2807 p
1749306806	27.6 C	47 p	142 p	2804 p
1749305606	28.1 C	49 p	154 p	2793 p
1749304406	27.4 C	46 p	159 p	2788 p
1749303206	27.7 C	59 p	157 p	2780 p
1749302006	26.6 C	54 p	139 p	2753 p
1749300806	26.8 C	44 p	120 p	2727 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)