APRS Track Direct

My position About ☰

reset

BV6BU-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BV6BU-15. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1790661969	43.6 C	4 p	11 p	337 p
1790660769	46 C	3 p	11 p	336 p
1790659569	46 C	4 p	17 p	337 p
1790658369	44.9 C	4 p	15 p	335 p
1790657169	45.4 C	9 p	14 p	334 p
1790655969	44.9 C	2 p	7 p	330 p
1790654769	45.5 C	3 p	12 p	330 p
1790653569	45.3 C	2 p	15 p	330 p
1790652370	45.7 C	7 p	22 p	331 p
1790651169	47 C	6 p	23 p	326 p
1790649970	48.2 C	9 p	27 p	324 p
1790648770	48.7 C	8 p	28 p	322 p
1790647570	47.7 C	10 p	31 p	323 p
1790646370	47.7 C	10 p	29 p	320 p
1790645169	47.1 C	11 p	29 p	318 p
1790643969	48.5 C	8 p	26 p	317 p
1790642769	48.6 C	10 p	20 p	319 p
1790641569	47.7 C	8 p	13 p	320 p
1790640369	46.5 C	2 p	9 p	329 p
1790639169	46.5 C	3 p	13 p	337 p
1790637969	45.2 C	4 p	15 p	339 p
1790636769	46.5 C	6 p	19 p	338 p
1790635570	45.8 C	5 p	19 p	336 p
1790634370	47 C	8 p	19 p	333 p
1790633170	46.5 C	6 p	16 p	329 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)