APRS Track Direct

My position About ☰

reset

N2RWE-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object N2RWE-13. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1786719103	13.8 Volt	120 Pkt	20 Pkt	29 Pcnt
1786717903	13.73 Volt	160 Pkt	30 Pkt	31 Pcnt
1786717303	12.68 Volt	160 Pkt	30 Pkt	30 Pcnt
1786716703	13.73 Volt	170 Pkt	30 Pkt	29 Pcnt
1786716104	12.9 Volt	170 Pkt	30 Pkt	30 Pcnt
1786715503	13.73 Volt	160 Pkt	30 Pkt	29 Pcnt
1786714905	13.73 Volt	140 Pkt	30 Pkt	26 Pcnt
1786714304	13.65 Volt	140 Pkt	40 Pkt	26 Pcnt
1786713707	13.65 Volt	150 Pkt	40 Pkt	30 Pcnt
1786708303	13.65 Volt	110 Pkt	20 Pkt	24 Pcnt
1786705303	13.65 Volt	120 Pkt	20 Pkt	27 Pcnt
1786703505	13.65 Volt	130 Pkt	30 Pkt	26 Pcnt
1786701704	13.65 Volt	170 Pkt	40 Pkt	29 Pcnt
1786700504	13.65 Volt	230 Pkt	50 Pkt	38 Pcnt
1786699304	13.65 Volt	230 Pkt	40 Pkt	40 Pcnt
1786698705	13.65 Volt	240 Pkt	50 Pkt	43 Pcnt
1786696905	13.65 Volt	250 Pkt	50 Pkt	46 Pcnt
1786693305	13.65 Volt	230 Pkt	30 Pkt	42 Pcnt
1786692105	13.65 Volt	230 Pkt	30 Pkt	40 Pcnt
1786691504	13.65 Volt	230 Pkt	30 Pkt	42 Pcnt
1786690904	13.65 Volt	220 Pkt	30 Pkt	42 Pcnt
1786690304	13.05 Volt	210 Pkt	30 Pkt	44 Pcnt
1786689704	13.65 Volt	200 Pkt	30 Pkt	44 Pcnt
1786689105	13.65 Volt	190 Pkt	20 Pkt	46 Pcnt
1786688505	13.65 Volt	160 Pkt	20 Pkt	44 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)