APRS Track Direct

My position About ☰

reset

SR9NRA Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR9NRA. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Rx10min*	Tx10min*	Digi10min*	Vbatt*
1732290224	46 Pkt	1 Pkt	1 Pkt	10 V
1732289624	46 Pkt	1 Pkt	0 Pkt	10 V
1732289024	47 Pkt	0 Pkt	0 Pkt	10 V
1732288424	41 Pkt	0 Pkt	0 Pkt	10 V
1732287824	46 Pkt	1 Pkt	1 Pkt	10 V
1732287224	34 Pkt	0 Pkt	0 Pkt	10 V
1732286624	53 Pkt	4 Pkt	0 Pkt	10 V
1732286013	68 Pkt	0 Pkt	0 Pkt	10 V
1732285413	68 Pkt	0 Pkt	0 Pkt	10 V
1732284813	69 Pkt	1 Pkt	0 Pkt	10 V
1732284213	69 Pkt	0 Pkt	0 Pkt	10 V
1732283614	56 Pkt	0 Pkt	0 Pkt	10 V
1732283014	54 Pkt	0 Pkt	0 Pkt	10 V
1732282414	46 Pkt	0 Pkt	0 Pkt	10 V
1732281814	48 Pkt	0 Pkt	0 Pkt	10 V
1732281214	42 Pkt	0 Pkt	0 Pkt	10 V
1732280614	61 Pkt	1 Pkt	0 Pkt	10 V
1732280014	47 Pkt	0 Pkt	0 Pkt	10 V
1732279415	60 Pkt	0 Pkt	0 Pkt	10 V
1732278815	49 Pkt	0 Pkt	0 Pkt	10 V
1732278215	55 Pkt	0 Pkt	0 Pkt	10 V
1732277615	50 Pkt	0 Pkt	0 Pkt	10 V
1732277015	52 Pkt	4 Pkt	0 Pkt	10 V
1732276407	36 Pkt	0 Pkt	0 Pkt	10 V
1732275807	40 Pkt	1 Pkt	0 Pkt	10 V

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Tx10min: 0, 1, 0

Digi10min: 0, 1, 0

Vbatt: 0, 0.02, 10

Tempre: 0, 0.5, -50

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)