APRS Track Direct

My position About ☰

reset

BV2CW-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BV2CW-9. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1836274381	37.8 C	130 p	371 p	7201 p
1762336267	33.4 C	24 p	142 p	1194 p
1762335067	32.3 C	56 p	183 p	1172 p
1762333867	33.1 C	62 p	167 p	1116 p
1762332667	33.9 C	66 p	133 p	1058 p
1762331466	32.2 C	39 p	88 p	1004 p
1762330267	32.8 C	28 p	82 p	978 p
1762329067	33.3 C	21 p	84 p	956 p
1762327866	32.7 C	33 p	91 p	940 p
1762326667	34.2 C	30 p	86 p	916 p
1762325467	33.6 C	28 p	87 p	896 p
1762324267	33.3 C	28 p	92 p	885 p
1762323067	34 C	31 p	91 p	886 p
1762321867	33.1 C	33 p	81 p	875 p
1762320666	33.3 C	27 p	78 p	867 p
1762319466	34.5 C	21 p	79 p	860 p
1762318266	33.8 C	30 p	83 p	843 p
1762317066	33.1 C	28 p	74 p	818 p
1762315867	33.9 C	25 p	66 p	805 p
1762314667	32.7 C	21 p	61 p	799 p
1762313467	33.3 C	20 p	58 p	796 p
1762312267	32.9 C	20 p	66 p	796 p
1762311066	33.4 C	18 p	77 p	797 p
1762309866	32.3 C	28 p	82 p	795 p
1762308666	32.8 C	31 p	74 p	789 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)