APRS Track Direct

My position About ☰

reset

YD0AVJ-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YD0AVJ-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RxTraffic*	RSSI*	Voltage*
1745003223	11 Pkt	-57 dBm	12.86 V
1745002900	19 Pkt	-55 dBm	12.86 V
1745002579	18 Pkt	-59 dBm	12.88 V
1745002255	17 Pkt	-55 dBm	12.86 V
1745001930	17 Pkt	-55 dBm	12.86 V
1745001606	17 Pkt	-54 dBm	12.86 V
1745001282	10 Pkt	-56 dBm	12.86 V
1745001092	18 Pkt	-53 dBm	12.86 V
1745000777	13 Pkt	-55 dBm	12.86 V
1745000449	17 Pkt	-57 dBm	12.86 V
1745000120	16 Pkt	-56 dBm	12.86 V
1744999799	13 Pkt	-53 dBm	12.86 V
1744999473	13 Pkt	-57 dBm	12.88 V
1744999150	18 Pkt	-56 dBm	12.86 V
1744998826	17 Pkt	-54 dBm	12.86 V
1744998507	16 Pkt	-53 dBm	12.86 V
1744998179	16 Pkt	-56 dBm	12.86 V
1744997855	10 Pkt	-56 dBm	12.84 V
1744997533	14 Pkt	-55 dBm	12.86 V
1744997210	13 Pkt	-54 dBm	12.86 V
1744996888	18 Pkt	-53 dBm	12.86 V
1744996563	16 Pkt	-55 dBm	12.86 V
1744996242	16 Pkt	-54 dBm	12.86 V
1744995917	17 Pkt	-54 dBm	12.86 V
1744995592	18 Pkt	-56 dBm	12.86 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)