APRS Track Direct

My position About ☰

reset

E24BD Telemetry

This is the latest recevied telemetry packets stored in our database for station/object E24BD. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	TxTraffic*	RSSI*	Voltage*
1731478950	0 Pkt	-83 dBm	0 V
1731478329	1 Pkt	-84 dBm	0.02 V
1731477706	0 Pkt	-83 dBm	0 V
1731477085	0 Pkt	-82 dBm	0 V
1731476463	0 Pkt	-79 dBm	0 V
1731475840	0 Pkt	-81 dBm	0.02 V
1731475219	0 Pkt	-82 dBm	0 V
1731474597	0 Pkt	-80 dBm	0.02 V
1731473975	0 Pkt	-81 dBm	0.02 V
1731473353	0 Pkt	-80 dBm	0.02 V
1731472730	1 Pkt	-81 dBm	0.02 V
1731472111	0 Pkt	-81 dBm	0.02 V
1731471486	0 Pkt	-82 dBm	0.02 V
1731470865	0 Pkt	-81 dBm	0 V
1731470243	1 Pkt	-81 dBm	0.02 V
1731469621	0 Pkt	-82 dBm	0 V
1731468998	1 Pkt	-82 dBm	0.02 V
1731468377	0 Pkt	-79 dBm	0.02 V
1731467754	0 Pkt	-81 dBm	0 V
1731467132	0 Pkt	-83 dBm	0.02 V
1731466510	0 Pkt	-83 dBm	0.02 V
1731465889	0 Pkt	-81 dBm	0.02 V
1731465266	0 Pkt	-80 dBm	0.02 V
1731464644	0 Pkt	-81 dBm	0.02 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)