APRS Track Direct

My position About ☰

reset

BM2OPC-6 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BM2OPC-6. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1790658449	45.9 C	0 p	0 p	1855 p
1790657249	44.7 C	0 p	0 p	1885 p
1790656049	46.2 C	0 p	0 p	1916 p
1790654856	44.7 C	0 p	0 p	1949 p
1790653649	45.3 C	0 p	0 p	1974 p
1790652449	44.7 C	0 p	0 p	2014 p
1790651249	46.8 C	0 p	0 p	2062 p
1790650049	46.5 C	0 p	31 p	2146 p
1790648848	47.5 C	0 p	68 p	2273 p
1790647649	46.4 C	31 p	99 p	2319 p
1790646449	45.2 C	37 p	114 p	2345 p
1790645249	45.7 C	31 p	117 p	2372 p
1790644049	46.5 C	46 p	124 p	2393 p
1790642849	45.7 C	40 p	119 p	2373 p
1790641649	44.7 C	38 p	125 p	2374 p
1790640449	44.9 C	41 p	122 p	2377 p
1790639249	47 C	46 p	102 p	2376 p
1790638049	44.2 C	35 p	73 p	2360 p
1790636850	45.3 C	21 p	83 p	2363 p
1790635649	45.8 C	17 p	83 p	2373 p
1790634449	46.8 C	45 p	86 p	2383 p
1790633249	47.9 C	21 p	69 p	2373 p
1790632050	48.1 C	20 p	75 p	2384 p
1790630849	48.3 C	28 p	82 p	2390 p
1790629649	49.9 C	27 p	87 p	2389 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)