APRS Track Direct

My position About ☰

reset

HS6KLJ-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS6KLJ-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	RF->INET*	AllCount*	AllDrop*
1778032699	8 Pkts	42 Pkts	18 Pkts
1778029099	12 Pkts	49 Pkts	23 Pkts
1778025498	2 Pkts	28 Pkts	15 Pkts
1778021898	7 Pkts	38 Pkts	16 Pkts
1778018298	5 Pkts	32 Pkts	16 Pkts
1778014698	3 Pkts	37 Pkts	19 Pkts
1778011098	10 Pkts	49 Pkts	28 Pkts
1778007498	8 Pkts	55 Pkts	27 Pkts
1778003898	9 Pkts	38 Pkts	15 Pkts
1778000298	8 Pkts	40 Pkts	18 Pkts
1777996698	8 Pkts	48 Pkts	26 Pkts
1777993098	6 Pkts	31 Pkts	17 Pkts
1777989498	6 Pkts	26 Pkts	16 Pkts
1777985898	1 Pkts	9 Pkts	8 Pkts
1777982298	3 Pkts	12 Pkts	9 Pkts
1777978698	4 Pkts	16 Pkts	12 Pkts
1777975097	1 Pkts	5 Pkts	4 Pkts
1777971497	3 Pkts	19 Pkts	10 Pkts
1777967897	3 Pkts	6 Pkts	3 Pkts
1777964297	2 Pkts	15 Pkts	11 Pkts
1777960697	2 Pkts	16 Pkts	11 Pkts
1777957097	1 Pkts	21 Pkts	12 Pkts
1777953497	2 Pkts	26 Pkts	13 Pkts

*Used Equation Coefficients:

RF->INET: 0, 1, 0

INET->RF: 0, 1, 0

Repeater: 0, 1, 0

AllCount: 0, 1, 0

AllDrop: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)