APRS Track Direct

My position About ☰

reset

YO8B-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YO8B-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	TRX*	Shelter*	Exterior*
1745051466	20.1 °C	32 °C	17.4 °C
1745050865	18.9 °C	30.8 °C	15.9 °C
1745050265	18.6 °C	30.4 °C	15.8 °C
1745049665	17.8 °C	30 °C	15.9 °C
1745049066	16.6 °C	29.8 °C	15 °C
1745048466	15.6 °C	29.7 °C	13.9 °C
1745047866	15.2 °C	29.5 °C	13.9 °C
1745047266	14.9 °C	29.6 °C	13.8 °C
1745046665	14.6 °C	29.5 °C	13.1 °C
1745046065	14.8 °C	29.5 °C	12.8 °C
1745045465	15 °C	29.1 °C	13.1 °C
1745044866	15 °C	29 °C	13.4 °C
1745044266	14.9 °C	28.8 °C	13.5 °C
1745043666	14.7 °C	28.7 °C	13.2 °C
1745043065	14.9 °C	28.6 °C	13.1 °C
1745042465	15.2 °C	28.5 °C	13.7 °C
1745041865	14.8 °C	28.4 °C	14.5 °C
1745041266	14.2 °C	28.3 °C	13.8 °C
1745040666	13.7 °C	28.2 °C	13.2 °C
1745040066	13.1 °C	28.3 °C	12.6 °C
1745039466	12.4 °C	28.6 °C	12.2 °C
1745038865	11.8 °C	28.9 °C	11.4 °C
1745038265	11.4 °C	29.4 °C	10.8 °C
1745037666	11.2 °C	30.1 °C	10.7 °C
1745037066	10.9 °C	30.9 °C	10.4 °C

*Used Equation Coefficients:

TRX: 0, 1, -100

Shelter: 0, 1, -100

Exterior: 0, 1, -100

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)