This is the latest recevied telemetry packets stored in our database for station/object SQ9P-9. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time | rx_cnt* | loss* | rx_tx* | napiecie* | temp* |
---|---|---|---|---|---|
1719428048 | 6 | 152 | 4 | 3.55 | 29 |
1719426302 | 245 | 77 | 5 | 3.53 | 28 |
1719425429 | 236 | 38 | 3 | 3.56 | 29 |
1719424556 | 226 | 251 | 3 | 3.55 | 29 |
1719423684 | 220 | 218 | 3 | 3.55 | 29 |
1719422811 | 211 | 178 | 0 | 3.56 | 29 |
1719421944 | 197 | 143 | 2 | 3.55 | 29 |
1719421065 | 188 | 109 | 4 | 3.55 | 29 |
1719420193 | 178 | 77 | 3 | 3.55 | 29 |
1719419320 | 164 | 47 | 4 | 3.55 | 29 |
1719418447 | 158 | 12 | 4 | 3.55 | 28 |
1719417574 | 147 | 236 | 2 | 3.56 | 29 |
1719416708 | 138 | 222 | 3 | 3.55 | 28 |
1719415829 | 126 | 192 | 4 | 3.55 | 28 |
1719414956 | 119 | 168 | 0 | 3.56 | 29 |
1719414084 | 112 | 138 | 0 | 3.56 | 29 |
1719413211 | 105 | 102 | 4 | 3.55 | 28 |
1719412339 | 99 | 61 | 0 | 3.56 | 28 |
1719411472 | 91 | 38 | 1 | 3.56 | 28 |
1719410594 | 84 | 10 | 0 | 3.56 | 28 |
1719409721 | 77 | 246 | 5 | 3.55 | 29 |
1719407976 | 54 | 176 | 5 | 3.55 | 28 |
1719407104 | 47 | 151 | 0 | 3.55 | 28 |
1719405359 | 27 | 96 | 0 | 3.56 | 28 |
1719404486 | 20 | 72 | 0 | 3.56 | 28 |
*Used Equation Coefficients:
rx_cnt: 0, 1, 0
loss: 0, 1, 0
rx_tx: 0, 1, 0
napiecie: 0, 0.01569, 0
temp: 0, 1, -128
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)