APRS Track Direct

My position About ☰

reset

YO8B-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YO8B-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TRX*	Shelter*	Exterior*
1770451266	17.1 °C	1.7 °C	0.1 °C
1770450665	17.8 °C	1.4 °C	0.4 °C
1770450065	17.9 °C	0.9 °C	-0.2 °C
1770449466	14.7 °C	0.2 °C	-0.3 °C
1770448866	14.6 °C	-0.4 °C	-0.6 °C
1770448266	14.9 °C	-0.8 °C	-0.9 °C
1770447666	15 °C	-0.9 °C	-1.2 °C
1770447066	15.1 °C	-1 °C	-1.2 °C
1770446465	15.4 °C	-1.4 °C	-1.6 °C
1770445865	15.6 °C	-1.6 °C	-1.6 °C
1770445265	16.1 °C	-1.8 °C	-1.8 °C
1770444666	16.7 °C	-1.9 °C	-2.1 °C
1770444066	17.3 °C	-2 °C	-2.1 °C
1770443466	18.2 °C	-2 °C	-2.2 °C
1770442865	19.4 °C	-2.1 °C	-2.2 °C
1770442265	20.8 °C	-2.1 °C	-2.2 °C
1770441665	22.5 °C	-2 °C	-2.1 °C
1770441066	24.9 °C	-1.9 °C	-2.1 °C
1770440466	27.9 °C	-1.9 °C	-2.1 °C
1770439866	31.9 °C	-1.8 °C	-2.1 °C
1770439265	35.4 °C	-1.8 °C	-2.2 °C
1770438665	41.4 °C	-1.7 °C	-2 °C
1770438065	35.8 °C	-1.8 °C	-2 °C
1770437466	36 °C	-1.7 °C	-1.9 °C
1770436866	36.9 °C	-1.9 °C	-2 °C

*Used Equation Coefficients:

TRX: 0, 1, -100

Shelter: 0, 1, -100

Exterior: 0, 1, -100

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)