APRS Track Direct

My position About ☰

reset

K2CSN-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object K2CSN-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	RFIn*	RFiGate*	DigiRpt*	Temp*
1732569006	20 Pkts	18 Pkts	3 Pkts	25 C
1732565406	20 Pkts	18 Pkts	7 Pkts	25 C
1732561806	22 Pkts	20 Pkts	9 Pkts	26 C
1732558206	31 Pkts	29 Pkts	11 Pkts	26 C
1732554606	32 Pkts	30 Pkts	12 Pkts	26 C
1732551007	31 Pkts	29 Pkts	10 Pkts	26 C
1732547407	36 Pkts	34 Pkts	11 Pkts	26 C
1732543806	24 Pkts	22 Pkts	11 Pkts	26 C
1732540207	28 Pkts	26 Pkts	9 Pkts	25 C
1732536607	39 Pkts	37 Pkts	10 Pkts	25 C
1732533007	33 Pkts	31 Pkts	11 Pkts	25 C
1732529406	35 Pkts	33 Pkts	12 Pkts	25 C
1732525806	27 Pkts	25 Pkts	10 Pkts	25 C
1732522206	29 Pkts	27 Pkts	8 Pkts	25 C
1732518606	29 Pkts	27 Pkts	11 Pkts	25 C
1732515006	36 Pkts	34 Pkts	13 Pkts	25 C
1732511406	32 Pkts	30 Pkts	14 Pkts	25 C
1732507807	34 Pkts	32 Pkts	12 Pkts	26 C
1732504207	24 Pkts	22 Pkts	9 Pkts	26 C

*Used Equation Coefficients:

RFIn: 0, 1, 0

RFiGate: 0, 1, 0

DigiRpt: 0, 1, 0

Temp: 0, 1, 0

InetiGate: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)