APRS Track Direct

My position About ☰

reset

BM5GST-8 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BM5GST-8. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1732227132	24.8 C	0 p	0 p	2386 p
1732225932	24.9 C	0 p	0 p	2466 p
1732224731	24.2 C	0 p	0 p	2526 p
1732223532	25.2 C	0 p	0 p	2550 p
1732222331	24.5 C	0 p	0 p	2572 p
1732221132	24.7 C	0 p	0 p	2598 p
1732219932	25.7 C	0 p	0 p	2617 p
1732218732	24.7 C	0 p	0 p	2637 p
1732217532	25.6 C	0 p	0 p	2659 p
1732216331	24.6 C	0 p	0 p	2678 p
1732215132	24.3 C	0 p	0 p	2702 p
1732213932	24.9 C	0 p	0 p	2723 p
1732212732	24.6 C	0 p	0 p	2744 p
1732211532	25.1 C	0 p	0 p	2763 p
1732210332	24.9 C	0 p	0 p	2782 p
1732209131	24.8 C	0 p	0 p	2803 p
1732207931	24.8 C	0 p	0 p	2823 p
1732206731	25.6 C	0 p	3 p	2842 p
1732205531	26 C	0 p	24 p	2878 p
1732204331	26.6 C	3 p	43 p	2909 p
1732203131	27.3 C	21 p	65 p	2928 p
1732201931	27.5 C	19 p	66 p	2928 p
1732200731	26.8 C	25 p	75 p	2944 p
1732199531	27.5 C	22 p	72 p	2954 p
1732198331	27.1 C	28 p	70 p	2952 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)