APRS Track Direct

My position About ☰

reset

VA3XLT-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VA3XLT-2. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1732223348	14.33 Volt	190 Pkt	30 Pkt	67 Pcnt
1732219745	14.33 Volt	140 Pkt	10 Pkt	72 Pcnt
1732216138	14.33 Volt	140 Pkt	10 Pkt	78 Pcnt
1732212539	14.33 Volt	190 Pkt	20 Pkt	72 Pcnt
1732208933	14.33 Volt	200 Pkt	10 Pkt	86 Pcnt
1732205329	14.33 Volt	130 Pkt	20 Pkt	93 Pcnt
1732201726	14.33 Volt	170 Pkt	20 Pkt	78 Pcnt
1732198124	14.33 Volt	190 Pkt	10 Pkt	66 Pcnt
1732194519	14.33 Volt	120 Pkt	0 Pkt	64 Pcnt
1732190916	14.33 Volt	150 Pkt	10 Pkt	53 Pcnt
1732187316	14.33 Volt	100 Pkt	0 Pkt	71 Pcnt
1732183707	14.33 Volt	90 Pkt	0 Pkt	73 Pcnt
1732180104	14.33 Volt	110 Pkt	0 Pkt	69 Pcnt
1732176504	14.33 Volt	110 Pkt	0 Pkt	61 Pcnt
1732172900	14.25 Volt	130 Pkt	0 Pkt	47 Pcnt
1732169297	14.25 Volt	100 Pkt	0 Pkt	43 Pcnt
1732165693	14.33 Volt	120 Pkt	0 Pkt	54 Pcnt
1732162086	14.33 Volt	90 Pkt	0 Pkt	55 Pcnt
1732158486	14.33 Volt	100 Pkt	0 Pkt	86 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Dg10M: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)