APRS Track Direct

My position About ☰

reset

DD3UTS-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DD3UTS-15. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Battery*	DrehWin*	BlitzD*
1745034931	12.9 V	124 n/min	100 km
1745034632	12.9 V	80 n/min	100 km
1745034331	12.9 V	80 n/min	100 km
1745034031	12.9 V	104 n/min	100 km
1745033731	12.9 V	52 n/min	100 km
1745033432	12.9 V	32 n/min	100 km
1745033131	12.9 V	12 n/min	100 km
1745032831	12.9 V	20 n/min	100 km
1745032532	12.9 V	12 n/min	100 km
1745032231	12.9 V	24 n/min	100 km
1745031931	12.9 V	40 n/min	100 km
1745031632	12.9 V	80 n/min	100 km
1745031332	12.9 V	8 n/min	100 km
1745031031	12.9 V	24 n/min	100 km
1745030731	12.9 V	80 n/min	100 km
1745030432	12.9 V	60 n/min	100 km
1745030132	12.9 V	28 n/min	100 km
1745029832	12.9 V	32 n/min	100 km
1745029532	12.9 V	60 n/min	100 km
1745029232	12.9 V	88 n/min	100 km
1745028932	12.9 V	44 n/min	100 km
1745028631	12.9 V	64 n/min	100 km
1745028332	12.9 V	80 n/min	100 km
1745028031	12.9 V	40 n/min	100 km
1745027731	12.9 V	56 n/min	100 km

*Used Equation Coefficients:

Battery: 0, 0.075, 0

DrehWin: 0, 4, 0

SolarP: 0, 4, 0

BlitzD: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)