APRS Track Direct

My position About ☰

reset

E27ARV-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object E27ARV-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	TxTraffic*	RSSI*	Voltage*
1791983056	0 Pkt	-55 dBm	0.31 V
1791982434	0 Pkt	-51 dBm	0.31 V
1791980591	0 Pkt	-51 dBm	0.31 V
1791978778	0 Pkt	-52 dBm	0.31 V
1791976954	0 Pkt	-52 dBm	0.29 V
1791976332	0 Pkt	-52 dBm	0.31 V
1791974518	0 Pkt	-52 dBm	0.78 V
1791973896	0 Pkt	-52 dBm	1.17 V
1791970464	0 Pkt	-52 dBm	4.72 V
1791965460	0 Pkt	-55 dBm	11.28 V
1791963258	0 Pkt	-55 dBm	11.53 V
1791961443	0 Pkt	-55 dBm	12.47 V
1791953265	0 Pkt	-56 dBm	12.47 V
1791952643	0 Pkt	-55 dBm	12.41 V
1791952021	0 Pkt	-57 dBm	12.57 V
1791951400	0 Pkt	-56 dBm	12.65 V
1791950777	2 Pkt	-56 dBm	12.47 V
1791950155	0 Pkt	-56 dBm	12.33 V
1791949533	2 Pkt	-59 dBm	12.3 V
1791948911	0 Pkt	-59 dBm	12.2 V
1791948289	0 Pkt	-57 dBm	12.1 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)