APRS Track Direct

My position About ☰

reset

BM3FFG-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BM3FFG-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1836274514	38.8 C	2 p	28 p	160 p
1774157085	39.2 C	6 p	14 p	365 p
1774155885	37.4 C	4 p	12 p	379 p
1774154685	38.3 C	4 p	13 p	383 p
1774153485	38.8 C	4 p	18 p	384 p
1774152286	37.3 C	5 p	26 p	389 p
1774151086	38.9 C	9 p	39 p	393 p
1774149885	37.4 C	12 p	71 p	409 p
1774148685	36.9 C	18 p	72 p	407 p
1774147486	36.1 C	41 p	56 p	420 p
1774146286	34.9 C	13 p	20 p	396 p
1774145085	36 C	2 p	13 p	435 p
1774143885	32.8 C	5 p	18 p	494 p
1774142686	34.4 C	6 p	16 p	543 p
1774141485	33.7 C	7 p	16 p	594 p
1774140285	33.4 C	3 p	14 p	616 p
1774139086	32.5 C	6 p	14 p	628 p
1774137885	33.1 C	5 p	13 p	633 p
1774136685	32.5 C	3 p	14 p	632 p
1774135486	32.5 C	5 p	15 p	633 p
1774134285	31 C	6 p	16 p	632 p
1774133085	32.7 C	4 p	11 p	629 p
1774131886	33.2 C	6 p	10 p	631 p
1774130685	32.3 C	1 p	6 p	631 p
1774129486	32 C	3 p	6 p	636 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)