APRS Track Direct

My position About ☰

reset

OE3XDC-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE3XDC-13. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*	Temp*
1745058946	11.93 Volt	340 Pkt	78 Pcnt	21 C
1745058646	11.93 Volt	360 Pkt	79 Pcnt	22 C
1745058346	12 Volt	360 Pkt	79 Pcnt	22 C
1745058046	11.93 Volt	370 Pkt	77 Pcnt	21 C
1745057746	12 Volt	360 Pkt	77 Pcnt	21 C
1745057446	12 Volt	360 Pkt	76 Pcnt	20.5 C
1745057146	11.93 Volt	360 Pkt	75 Pcnt	20.5 C
1745056846	11.93 Volt	360 Pkt	76 Pcnt	21 C
1745056546	11.85 Volt	340 Pkt	75 Pcnt	21.5 C
1745056246	12 Volt	330 Pkt	75 Pcnt	20 C
1745055946	11.78 Volt	310 Pkt	72 Pcnt	20.5 C
1745055646	12 Volt	300 Pkt	72 Pcnt	20.5 C
1745055346	11.93 Volt	300 Pkt	71 Pcnt	20.5 C
1745055046	11.85 Volt	310 Pkt	71 Pcnt	20 C
1745054746	12 Volt	300 Pkt	70 Pcnt	20 C
1745054446	11.93 Volt	310 Pkt	70 Pcnt	19 C
1745054146	12 Volt	310 Pkt	70 Pcnt	19 C
1745053846	12 Volt	310 Pkt	70 Pcnt	20 C
1745053546	12 Volt	310 Pkt	69 Pcnt	19.5 C
1745053246	12.08 Volt	320 Pkt	69 Pcnt	19.5 C
1745052946	12 Volt	320 Pkt	69 Pcnt	19.5 C
1745052646	11.78 Volt	330 Pkt	70 Pcnt	19.5 C
1745052346	12 Volt	340 Pkt	71 Pcnt	19.5 C
1745052046	12.08 Volt	340 Pkt	70 Pcnt	18.5 C
1745051746	12 Volt	350 Pkt	72 Pcnt	18 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)