APRS Track Direct

My position About ☰

reset

YB8VJT-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YB8VJT-13. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1763483367	0 Pkt	-73 dBm	0 V
1763483045	0 Pkt	-68 dBm	0.1 V
1763482723	0 Pkt	-70 dBm	0.55 V
1763482401	0 Pkt	-69 dBm	0.78 V
1763482079	0 Pkt	-72 dBm	0.02 V
1763481757	0 Pkt	-70 dBm	0 V
1763481435	0 Pkt	-71 dBm	0.1 V
1763481113	0 Pkt	-72 dBm	0.82 V
1763480791	0 Pkt	-73 dBm	0.02 V
1763480469	0 Pkt	-72 dBm	0 V
1763480147	0 Pkt	-73 dBm	0 V
1763479825	0 Pkt	-72 dBm	0.41 V
1763479503	0 Pkt	-71 dBm	0.08 V
1763479181	0 Pkt	-71 dBm	0.76 V
1763478859	0 Pkt	-72 dBm	0.21 V
1763478537	0 Pkt	-72 dBm	0 V
1763478215	0 Pkt	-70 dBm	0 V
1763477893	0 Pkt	-69 dBm	0.45 V
1763477571	0 Pkt	-72 dBm	0 V
1763477249	0 Pkt	-70 dBm	0 V
1763476927	0 Pkt	-71 dBm	0.51 V
1763476605	0 Pkt	-70 dBm	0 V
1763476283	0 Pkt	-70 dBm	0.06 V
1763475961	1 Pkt	-71 dBm	0.02 V
1763475639	0 Pkt	-71 dBm	0.02 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)