APRS Track Direct

My position About ☰

reset

TA7FTH-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TA7FTH-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	TxTraffic*	RSSI*	Voltage*
1732206778	33 Pkt	-73 dBm	3.83 V
1732205854	32 Pkt	-73 dBm	3.86 V
1732204930	70 Pkt	-74 dBm	3.83 V
1732204001	53 Pkt	-73 dBm	3.86 V
1732203075	44 Pkt	-72 dBm	3.86 V
1732202150	47 Pkt	-71 dBm	3.79 V
1732201224	55 Pkt	-72 dBm	3.86 V
1732200298	35 Pkt	-71 dBm	3.83 V
1732199373	33 Pkt	-72 dBm	3.86 V
1732198449	32 Pkt	-72 dBm	3.83 V
1732197523	2 Pkt	-71 dBm	3.86 V
1732197303	42 Pkt	-72 dBm	3.86 V
1732196378	32 Pkt	-71 dBm	3.83 V
1732195455	27 Pkt	-71 dBm	3.83 V
1732194531	35 Pkt	-73 dBm	3.83 V
1732193606	45 Pkt	-76 dBm	3.83 V
1732192682	41 Pkt	-74 dBm	3.86 V
1732191757	47 Pkt	-74 dBm	3.86 V
1732190830	29 Pkt	-74 dBm	3.83 V
1732189906	31 Pkt	-74 dBm	3.83 V
1732188980	29 Pkt	-74 dBm	3.86 V
1732188055	25 Pkt	-75 dBm	3.86 V
1732187130	30 Pkt	-74 dBm	3.83 V
1732186206	27 Pkt	-74 dBm	3.83 V
1732185282	27 Pkt	-74 dBm	3.83 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)