This is the latest recevied telemetry packets stored in our database for station/object KC4UG-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time | Value1* | Value2* | Value3* | Value4* | Value5* |
---|---|---|---|---|---|
1731565347 | 255 | 178 | 137 | 102 | 63 |
1731564684 | 255 | 178 | 138 | 102 | 63 |
1731564023 | 255 | 178 | 137 | 101 | 62 |
1731563362 | 255 | 178 | 137 | 102 | 64 |
1731562039 | 255 | 178 | 138 | 102 | 63 |
1731561377 | 255 | 178 | 138 | 103 | 63 |
1731560716 | 255 | 178 | 137 | 102 | 61 |
1731560054 | 255 | 181 | 139 | 103 | 63 |
1731559392 | 255 | 177 | 138 | 102 | 66 |
1731558733 | 255 | 181 | 139 | 103 | 62 |
1731558068 | 255 | 181 | 139 | 103 | 62 |
1731557407 | 255 | 181 | 139 | 103 | 64 |
1731556084 | 255 | 178 | 137 | 102 | 65 |
1731555422 | 255 | 177 | 137 | 102 | 63 |
1731554761 | 255 | 177 | 138 | 102 | 62 |
1731554099 | 255 | 178 | 137 | 102 | 61 |
1731552776 | 255 | 178 | 138 | 102 | 63 |
1731552114 | 255 | 178 | 138 | 103 | 63 |
1731551453 | 255 | 177 | 137 | 102 | 63 |
1731550791 | 255 | 178 | 138 | 103 | 63 |
*Used Equation Coefficients:
Value1: 0, 1, 0
Value2: 0, 1, 0
Value3: 0, 1, 0
Value4: 0, 1, 0
Value5: 0, 1, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)