APRS Track Direct

My position About ☰

reset

MTVVPC Telemetry

This is the latest recevied telemetry packets stored in our database for station/object MTVVPC. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	SOC*	Capacity*	Voltage*	Current*	Temp*
1786747747	100 %	100 Ah	54 V	0 A	24 C
1786747149	100 %	100 Ah	54 V	0 A	24 C
1786744747	100 %	100 Ah	54 V	0 A	24 C
1786742946	100 %	100 Ah	54 V	0 A	24 C
1786741749	100 %	100 Ah	54 V	0 A	24 C
1786740546	100 %	100 Ah	54 V	0 A	23 C
1786739948	100 %	100 Ah	54 V	0 A	23 C
1786738148	100 %	100 Ah	54 V	0 A	23 C
1786734548	100 %	100 Ah	54 V	0 A	23 C
1786733946	100 %	100 Ah	54 V	0 A	23 C
1786732748	100 %	100 Ah	54 V	0 A	23 C
1786729745	97 %	97 Ah	51 V	4 A	23 C
1786729148	97 %	97 Ah	51 V	3 A	23 C
1786727946	97 %	97 Ah	51 V	3 A	23 C
1786727348	97 %	97 Ah	51 V	3 A	23 C
1786726746	97 %	97 Ah	50 V	3 A	23 C
1786726145	97 %	97 Ah	50 V	2 A	23 C
1786724945	97 %	97 Ah	50 V	2 A	23 C
1786724345	97 %	97 Ah	50 V	2 A	23 C
1786722545	97 %	97 Ah	50 V	1 A	23 C
1786717145	97 %	97 Ah	50 V	0 A	24 C
1786715344	97 %	97 Ah	50 V	-1 A	24 C
1786714145	97 %	97 Ah	50 V	-1 A	24 C
1786713545	97 %	97 Ah	50 V	-1 A	24 C
1786712946	97 %	97 Ah	50 V	0 A	24 C

*Used Equation Coefficients:

SOC: 0, 1, 0

Capacity: 0, 1, 0

Voltage: 0, 1, 0

Current: 0, 1, -128

Temp: 0, 1, -40

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)