APRS Track Direct

My position About ☰

reset

BM6HIP-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BM6HIP-13. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1732567732	21.9 C	36 p	94 p	2955 p
1732566531	21.8 C	26 p	85 p	2988 p
1732565332	21.4 C	32 p	87 p	3034 p
1732564131	21.9 C	27 p	85 p	3051 p
1732562932	21.6 C	28 p	92 p	3054 p
1732561731	22.4 C	30 p	92 p	3095 p
1732560532	21.3 C	34 p	86 p	3124 p
1732559331	22.8 C	28 p	77 p	3145 p
1732558132	21.9 C	24 p	71 p	3188 p
1732556932	21.4 C	25 p	71 p	3234 p
1732555731	22.2 C	22 p	75 p	3237 p
1732554532	22.3 C	24 p	77 p	3240 p
1732553332	21.1 C	29 p	80 p	3241 p
1732552132	21.6 C	24 p	85 p	3239 p
1732550932	22.4 C	27 p	89 p	3241 p
1732549732	22.3 C	34 p	91 p	3236 p
1732548532	22 C	28 p	96 p	3243 p
1732547332	21.8 C	29 p	93 p	3284 p
1732546132	21.8 C	39 p	89 p	3330 p
1732544932	22 C	25 p	71 p	3356 p
1732543732	22.3 C	25 p	67 p	3404 p
1732542531	22 C	21 p	93 p	3443 p
1732541332	22 C	21 p	140 p	3458 p
1732540131	21.6 C	51 p	187 p	3492 p
1732538932	22.4 C	68 p	182 p	3465 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)