APRS Track Direct

My position About ☰

reset

LU7FDV-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LU7FDV-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	TxTraffic*	RSSI*	Voltage*
1732265966	2 Pkt	-87 dBm	9.39 V
1732265043	0 Pkt	-89 dBm	9.41 V
1732264121	0 Pkt	-88 dBm	9.41 V
1732263199	0 Pkt	-85 dBm	9.41 V
1732262277	0 Pkt	-88 dBm	9.39 V
1732261355	1 Pkt	-87 dBm	9.39 V
1732260433	1 Pkt	-89 dBm	9.39 V
1732259511	0 Pkt	-89 dBm	9.39 V
1732258589	0 Pkt	-89 dBm	9.41 V
1732257667	0 Pkt	-87 dBm	9.39 V
1732256745	1 Pkt	-88 dBm	9.39 V
1732255823	2 Pkt	-89 dBm	9.39 V
1732254901	1 Pkt	-86 dBm	9.39 V
1732253979	1 Pkt	-91 dBm	9.41 V
1732253057	0 Pkt	-86 dBm	9.43 V
1732252135	0 Pkt	-88 dBm	9.41 V
1732251213	0 Pkt	-88 dBm	9.43 V
1732250291	0 Pkt	-87 dBm	9.39 V
1732249369	0 Pkt	-86 dBm	9.41 V
1732248447	0 Pkt	-86 dBm	9.41 V
1732247525	0 Pkt	-88 dBm	9.41 V
1732246603	0 Pkt	-85 dBm	9.41 V
1732245681	0 Pkt	-85 dBm	9.41 V
1732244759	0 Pkt	-89 dBm	9.41 V
1732243837	0 Pkt	-90 dBm	9.39 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)