APRS Track Direct

My position About ☰

reset

OTISMA Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OTISMA. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx1h*	Dg1h*	Eff1h*
1732290314	140 Pkt	110 Pkt	69 Pcnt
1732290014	140 Pkt	110 Pkt	70 Pcnt
1732289714	150 Pkt	120 Pkt	73 Pcnt
1732289413	150 Pkt	120 Pkt	75 Pcnt
1732289113	160 Pkt	120 Pkt	76 Pcnt
1732288813	160 Pkt	120 Pkt	78 Pcnt
1732288513	160 Pkt	120 Pkt	80 Pcnt
1732288212	170 Pkt	130 Pkt	83 Pcnt
1732287912	170 Pkt	130 Pkt	83 Pcnt
1732287612	180 Pkt	140 Pkt	85 Pcnt
1732287312	190 Pkt	140 Pkt	86 Pcnt
1732287011	180 Pkt	140 Pkt	85 Pcnt
1732286711	180 Pkt	140 Pkt	85 Pcnt
1732286411	180 Pkt	140 Pkt	85 Pcnt
1732286110	170 Pkt	130 Pkt	86 Pcnt
1732285810	170 Pkt	130 Pkt	86 Pcnt
1732285510	180 Pkt	140 Pkt	86 Pcnt
1732285210	180 Pkt	140 Pkt	87 Pcnt
1732284909	180 Pkt	140 Pkt	86 Pcnt
1732284609	180 Pkt	140 Pkt	86 Pcnt
1732284309	180 Pkt	140 Pkt	86 Pcnt
1732284008	180 Pkt	140 Pkt	86 Pcnt
1732283708	180 Pkt	130 Pkt	85 Pcnt
1732283408	190 Pkt	140 Pkt	86 Pcnt
1732283108	190 Pkt	140 Pkt	88 Pcnt

*Used Equation Coefficients:

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A4: 0, 0, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)