APRS Track Direct

My position About ☰

reset

9M2HER Telemetry

This is the latest recevied telemetry packets stored in our database for station/object 9M2HER. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	TxTraffic*	RSSI*	Voltage*
1732289240	55 Pkt	-75 dBm	5.27 V
1732288012	46 Pkt	-75 dBm	5.23 V
1732286785	39 Pkt	-75 dBm	5.25 V
1732285559	49 Pkt	-75 dBm	5.25 V
1732284332	42 Pkt	-75 dBm	5.23 V
1732283105	112 Pkt	-75 dBm	5.25 V
1732281877	69 Pkt	-75 dBm	5.23 V
1732280649	38 Pkt	-75 dBm	5.23 V
1732279422	42 Pkt	-76 dBm	5.25 V
1732278196	4 Pkt	-76 dBm	5.23 V
1732277228	47 Pkt	-76 dBm	5.25 V
1732276001	76 Pkt	-73 dBm	5.25 V
1732274774	37 Pkt	-74 dBm	5.25 V
1732273547	57 Pkt	-74 dBm	5.25 V
1732272320	63 Pkt	-75 dBm	5.25 V
1732271093	53 Pkt	-76 dBm	5.25 V
1732269866	88 Pkt	-77 dBm	5.25 V
1732268639	39 Pkt	-77 dBm	5.27 V
1732267400	23 Pkt	-76 dBm	5.25 V
1732266174	42 Pkt	-76 dBm	5.25 V
1732264947	2 Pkt	-77 dBm	5.25 V
1732264821	53 Pkt	31 dBm	5.27 V
1732263587	117 Pkt	-76 dBm	5.27 V
1732262356	82 Pkt	-77 dBm	5.25 V
1732261130	49 Pkt	-77 dBm	5.25 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)