APRS Track Direct

My position About ☰

reset

SQ8JS Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SQ8JS. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	V12*	I*	T_bat*
1732286846	12.53 V	-20.68 A	1.5 C
1732286546	12.53 V	-20.68 A	1.5 C
1732286246	12.53 V	-20.68 A	1.5 C
1732285946	12.53 V	-20.68 A	1.5 C
1732285646	12.53 V	-20.68 A	1.5 C
1732285346	12.53 V	-20.68 A	1.5 C
1732285046	12.53 V	-20.68 A	1.5 C
1732284746	12.53 V	-20.68 A	1.5 C
1732284446	12.53 V	-20.68 A	1.5 C
1732284146	12.53 V	-20.68 A	1.5 C
1732283846	12.53 V	-20.68 A	1.5 C
1732283546	12.53 V	-20.68 A	1.5 C
1732283246	12.6 V	-20.68 A	1.5 C
1732282946	12.6 V	-20.68 A	1.5 C
1732282646	12.53 V	-20.68 A	1.5 C
1732282346	12.53 V	-20.68 A	1.5 C
1732282046	12.53 V	-20.68 A	1.5 C
1732281746	12.53 V	-20.68 A	1.5 C
1732281446	12.6 V	-20.68 A	1.5 C
1732281146	12.53 V	-20.68 A	1.5 C
1732280846	12.53 V	-20.68 A	1.5 C
1732280546	12.53 V	-20.68 A	1.5 C
1732280246	12.6 V	-20.68 A	1.5 C
1732279946	12.53 V	-20.68 A	2 C
1732279646	12.53 V	-20.68 A	2 C

*Used Equation Coefficients:

V24: 0, 0.1035, 0

V12: 0, 0.075, 0

I: -0.00655, 1, -20.6847

T_out: 0, 0.5, -64

T_bat: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)