APRS Track Direct

My position About ☰

reset

BX2AHP-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BX2AHP-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	CPUTemp*	RxPkts/10m*	RxPkts/1h*	RxPkts/24h*
1732294157	47 C	6 p	33 p	1188 p
1732292957	47 C	4 p	33 p	1176 p
1732291758	47 C	7 p	33 p	1166 p
1732290558	47 C	6 p	48 p	1155 p
1732289358	47 C	4 p	43 p	1143 p
1732288158	47 C	6 p	34 p	1133 p
1732286958	47 C	6 p	9 p	1107 p
1732285758	47 C	0 p	33 p	1100 p
1732284558	47 C	1 p	62 p	1099 p
1732283358	47 C	11 p	86 p	1098 p
1732282159	47 C	14 p	67 p	1067 p
1732280958	47 C	21 p	65 p	1037 p
1732279758	47 C	6 p	58 p	1012 p
1732278558	47 C	10 p	58 p	1000 p
1732277357	47 C	13 p	66 p	972 p
1732276157	48 C	6 p	100 p	954 p
1732274957	47 C	7 p	171 p	942 p
1732273757	47 C	22 p	199 p	906 p
1732272558	47 C	40 p	184 p	854 p
1732271357	47 C	37 p	153 p	771 p
1732270157	47 C	27 p	134 p	707 p
1732268957	47 C	23 p	136 p	670 p
1732267757	47 C	14 p	98 p	618 p
1732266557	47 C	26 p	63 p	573 p
1732265357	47 C	8 p	34 p	534 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/10m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)