APRS Track Direct

My position About ☰

reset

IR1BY Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IR1BY. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*	Temp*
1786733675	14.03 Volt	330 Pkt	67 Pcnt	24.5 C
1786731875	14.03 Volt	350 Pkt	69 Pcnt	25.5 C
1786730978	14.03 Volt	350 Pkt	69 Pcnt	26.5 C
1786730075	14.03 Volt	360 Pkt	72 Pcnt	28 C
1786729177	14.03 Volt	380 Pkt	76 Pcnt	29.5 C
1786728275	14.03 Volt	370 Pkt	82 Pcnt	27.5 C
1786727378	14.03 Volt	360 Pkt	84 Pcnt	25.5 C
1786726475	14.03 Volt	330 Pkt	85 Pcnt	25.5 C
1786725578	14.03 Volt	300 Pkt	82 Pcnt	26.5 C
1786724675	14.03 Volt	310 Pkt	84 Pcnt	27 C
1786722875	13.95 Volt	360 Pkt	87 Pcnt	28 C
1786721075	13.95 Volt	380 Pkt	87 Pcnt	38 C
1786720178	13.95 Volt	390 Pkt	89 Pcnt	43 C
1786719275	13.95 Volt	350 Pkt	92 Pcnt	44 C
1786717475	13.95 Volt	280 Pkt	95 Pcnt	40 C
1786715680	14.03 Volt	260 Pkt	94 Pcnt	36.5 C
1786715675	14.03 Volt	260 Pkt	94 Pcnt	36.5 C
1786714778	14.03 Volt	280 Pkt	93 Pcnt	31 C
1786713875	13.95 Volt	290 Pkt	95 Pcnt	29.5 C
1786712075	13.95 Volt	310 Pkt	96 Pcnt	38 C
1786709378	13.95 Volt	320 Pkt	91 Pcnt	36 C
1786708480	13.95 Volt	290 Pkt	88 Pcnt	35 C
1786708476	13.95 Volt	290 Pkt	88 Pcnt	35 C
1786706676	13.95 Volt	260 Pkt	85 Pcnt	33 C
1786705778	13.95 Volt	260 Pkt	88 Pcnt	32.5 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)