APRS Track Direct

My position About ☰

reset

CA3DPI-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object CA3DPI-13. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1750172207	0 Pkt	-69 dBm	21 V
1750171883	0 Pkt	-67 dBm	21 V
1750171558	0 Pkt	-67 dBm	21 V
1750171234	0 Pkt	-68 dBm	21 V
1750170910	0 Pkt	-69 dBm	21 V
1750170586	0 Pkt	-68 dBm	21 V
1750170262	0 Pkt	-68 dBm	21 V
1750169938	0 Pkt	-69 dBm	21 V
1750169613	0 Pkt	-69 dBm	21 V
1750169289	1 Pkt	-70 dBm	21 V
1750168963	0 Pkt	-69 dBm	21 V
1750168639	0 Pkt	-68 dBm	21 V
1750168314	0 Pkt	-70 dBm	21 V
1750167990	0 Pkt	-67 dBm	21 V
1750167665	1 Pkt	-71 dBm	21 V
1750167340	0 Pkt	-70 dBm	21 V
1750167016	0 Pkt	-71 dBm	21 V
1750166691	0 Pkt	-72 dBm	21 V
1750166367	0 Pkt	-70 dBm	21 V
1750166043	0 Pkt	-71 dBm	21 V
1750165719	0 Pkt	-70 dBm	21 V
1750165395	0 Pkt	-71 dBm	21 V
1750165071	0 Pkt	-70 dBm	21 V
1750164746	0 Pkt	-70 dBm	21 V
1750164421	0 Pkt	-70 dBm	21 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)