This is the latest recevied telemetry packets stored in our database for station/object BH9BG-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time | CPUTemp* | DiGi* | Tx* | Rx* | Value5* |
---|---|---|---|---|---|
1719663946 | 58 C | 0 p | 45 p | 160 p | 0 |
1719663266 | 59 C | 0 p | 45 p | 160 p | 0 |
1719663266 | 58 C | 0 p | 44 p | 155 p | 0 |
1719662478 | 58 C | 0 p | 43 p | 149 p | 0 |
1719661998 | 57 C | 0 p | 43 p | 145 p | 0 |
1719661689 | 58 C | 0 p | 42 p | 138 p | 0 |
1719661505 | 59 C | 0 p | 41 p | 133 p | 0 |
1719661085 | 58 C | 0 p | 41 p | 127 p | 0 |
1719660341 | 59 C | 0 p | 40 p | 124 p | 0 |
1719659881 | 59 C | 0 p | 40 p | 119 p | 0 |
1719659447 | 58 C | 0 p | 39 p | 114 p | 0 |
1719659060 | 59 C | 0 p | 38 p | 107 p | 0 |
1719658603 | 60 C | 0 p | 38 p | 102 p | 0 |
1719658182 | 63 C | 0 p | 37 p | 100 p | 0 |
1719657762 | 61 C | 0 p | 36 p | 99 p | 0 |
1719657344 | 63 C | 0 p | 36 p | 99 p | 0 |
1719656922 | 64 C | 0 p | 35 p | 99 p | 0 |
1719656502 | 64 C | 0 p | 34 p | 99 p | 0 |
1719656082 | 64 C | 0 p | 34 p | 99 p | 0 |
1719655663 | 63 C | 0 p | 33 p | 99 p | 0 |
1719655243 | 65 C | 0 p | 33 p | 99 p | 0 |
1719654942 | 65 C | 0 p | 31 p | 99 p | 0 |
1719654523 | 64 C | 0 p | 31 p | 99 p | 0 |
1719654103 | 64 C | 0 p | 30 p | 99 p | 0 |
1719653682 | 65 C | 0 p | 30 p | 99 p | 0 |
*Used Equation Coefficients:
CPUTemp: 0, 1, 0
DiGi: 0, 1, 0
Tx: 0, 1, 0
Rx: 0, 1, 0
Value5: 0, 1, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)