APRS Track Direct

My position About ☰

reset

YC1JEA-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YC1JEA-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1732290072	0 Pkt	-62 dBm	4.02 V
1732289762	0 Pkt	-62 dBm	4.02 V
1732289452	0 Pkt	-61 dBm	4.06 V
1732289142	0 Pkt	-62 dBm	4.06 V
1732288832	0 Pkt	-62 dBm	4.06 V
1732288522	0 Pkt	-62 dBm	4.04 V
1732288212	0 Pkt	-61 dBm	4.04 V
1732287902	0 Pkt	-61 dBm	5.19 V
1732287592	0 Pkt	-60 dBm	5.19 V
1732287282	0 Pkt	-60 dBm	5.21 V
1732286972	0 Pkt	-60 dBm	5.19 V
1732286662	0 Pkt	-60 dBm	5.13 V
1732286352	0 Pkt	-61 dBm	5.09 V
1732286042	0 Pkt	-63 dBm	21 V
1732285732	0 Pkt	-58 dBm	21 V
1732285422	0 Pkt	-60 dBm	21 V
1732285112	0 Pkt	-58 dBm	21 V
1732284802	1 Pkt	-57 dBm	21 V
1732284492	0 Pkt	-61 dBm	21 V
1732284182	0 Pkt	-60 dBm	21 V
1732283872	0 Pkt	-60 dBm	21 V
1732283562	0 Pkt	-61 dBm	21 V
1732283252	0 Pkt	-64 dBm	21 V
1732282942	0 Pkt	-64 dBm	21 V
1732282632	0 Pkt	-58 dBm	21 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)