APRS Track Direct

My position About ☰

reset

BX4ACP-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BX4ACP-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	CPUTemp*	RxPkts/10m*	RxPkts/1h*	RxPkts/24h*
1732298462	41 C	8 p	63 p	2713 p
1732297262	41 C	10 p	63 p	2692 p
1732296062	42 C	9 p	64 p	2670 p
1732294862	41 C	8 p	64 p	2650 p
1732293662	41 C	10 p	63 p	2629 p
1732292462	42 C	8 p	64 p	2606 p
1732291262	41 C	8 p	86 p	2586 p
1732290062	41 C	9 p	122 p	2566 p
1732288862	41 C	17 p	154 p	2542 p
1732287662	41 C	26 p	165 p	2500 p
1732286462	42 C	32 p	170 p	2444 p
1732285261	42 C	29 p	151 p	2388 p
1732284061	41 C	33 p	146 p	2335 p
1732282861	41 C	21 p	106 p	2274 p
1732281662	42 C	33 p	93 p	2237 p
1732280462	43 C	10 p	62 p	2189 p
1732279262	42 C	8 p	60 p	2168 p
1732278062	42 C	9 p	57 p	2144 p
1732276861	42 C	8 p	59 p	2127 p
1732275662	42 C	9 p	93 p	2108 p
1732274461	43 C	8 p	120 p	2087 p
1732273262	47 C	16 p	150 p	2068 p
1732272061	42 C	25 p	149 p	2015 p
1732270861	44 C	19 p	146 p	1967 p
1732269661	42 C	30 p	171 p	1918 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/10m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)