This is the latest recevied telemetry packets stored in our database for station/object OE5WWO-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time | RX1h* | Rx10m* | Eff1h* | Total* | Vin* |
---|---|---|---|---|---|
1731478208 | 0 Pkt | 1 Pkt | 12 Pcnt | 11 Pcnt | 0 Volt |
1731477308 | 0 Pkt | 0 Pkt | 12 Pcnt | 11 Pcnt | 0 Volt |
1731476406 | 0 Pkt | 1 Pkt | 14 Pcnt | 11 Pcnt | 0 Volt |
1731475506 | 0 Pkt | 1 Pkt | 14 Pcnt | 11 Pcnt | 0 Volt |
1731474605 | 0 Pkt | 0 Pkt | 16 Pcnt | 11 Pcnt | 0 Volt |
1731473704 | 0 Pkt | 1 Pkt | 13 Pcnt | 11 Pcnt | 0 Volt |
1731472803 | 10 Pkt | 3 Pkt | 15 Pcnt | 11 Pcnt | 0 Volt |
1731471902 | 10 Pkt | 1 Pkt | 17 Pcnt | 11 Pcnt | 0 Volt |
1731471001 | 10 Pkt | 0 Pkt | 19 Pcnt | 11 Pcnt | 0 Volt |
1731470100 | 10 Pkt | 2 Pkt | 22 Pcnt | 11 Pcnt | 0 Volt |
1731469200 | 10 Pkt | 3 Pkt | 20 Pcnt | 11 Pcnt | 0 Volt |
1731468299 | 10 Pkt | 2 Pkt | 19 Pcnt | 11 Pcnt | 0 Volt |
1731467398 | 0 Pkt | 2 Pkt | 14 Pcnt | 11 Pcnt | 0 Volt |
1731466497 | 0 Pkt | 2 Pkt | 12 Pcnt | 11 Pcnt | 0 Volt |
1731465596 | 0 Pkt | 2 Pkt | 12 Pcnt | 11 Pcnt | 0 Volt |
1731464695 | 0 Pkt | 1 Pkt | 10 Pcnt | 11 Pcnt | 0 Volt |
*Used Equation Coefficients:
RX1h: 0, 10, 0
Rx10m: 0, 1, 0
Eff1h: 0, 1, 0
Total: 0, 1, 0
Vin: 0, 0.079, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)