APRS Track Direct

My position About ☰

reset

TA4RE-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TA4RE-4. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	RxTraffic*	RSSI*	Voltage*
1786727088	0 Pkt	31 dBm	11.75 V
1786725265	0 Pkt	31 dBm	11.75 V
1786723442	0 Pkt	31 dBm	11.75 V
1786721618	0 Pkt	31 dBm	11.75 V
1786719794	0 Pkt	31 dBm	11.75 V
1786717970	1 Pkt	31 dBm	11.75 V
1786716146	3 Pkt	31 dBm	11.75 V
1786714322	3 Pkt	31 dBm	11.75 V
1786712498	0 Pkt	31 dBm	11.75 V
1786710674	6 Pkt	31 dBm	11.75 V
1786708849	5 Pkt	31 dBm	11.75 V
1786707025	6 Pkt	31 dBm	11.77 V
1786703376	24 Pkt	31 dBm	11.75 V
1786701550	2 Pkt	31 dBm	11.73 V
1786697902	1 Pkt	31 dBm	11.75 V
1786696078	6 Pkt	31 dBm	11.77 V
1786694254	14 Pkt	31 dBm	11.75 V
1786692427	5 Pkt	31 dBm	11.75 V
1786690603	4 Pkt	31 dBm	11.75 V
1786688779	0 Pkt	31 dBm	11.73 V
1786687342	9 Pkt	-93 dBm	11.75 V
1786685518	11 Pkt	-88 dBm	11.73 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)