APRS Track Direct

My position About ☰

reset

LZ0SLI Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LZ0SLI. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx1h*	EffTo*	Eff1*
1790643216	150 Pkt	78 Pcnt	74 Pcnt
1790642916	150 Pkt	78 Pcnt	76 Pcnt
1790642616	140 Pkt	78 Pcnt	75 Pcnt
1790642316	160 Pkt	78 Pcnt	76 Pcnt
1790642016	160 Pkt	78 Pcnt	76 Pcnt
1790641716	150 Pkt	78 Pcnt	76 Pcnt
1790641416	150 Pkt	78 Pcnt	76 Pcnt
1790641116	160 Pkt	78 Pcnt	77 Pcnt
1790640816	160 Pkt	78 Pcnt	78 Pcnt
1790640516	160 Pkt	78 Pcnt	78 Pcnt
1790640216	160 Pkt	78 Pcnt	80 Pcnt
1790639916	150 Pkt	78 Pcnt	80 Pcnt
1790639616	150 Pkt	78 Pcnt	81 Pcnt
1790639316	150 Pkt	78 Pcnt	81 Pcnt
1790639016	140 Pkt	78 Pcnt	82 Pcnt
1790638716	150 Pkt	78 Pcnt	82 Pcnt
1790638416	140 Pkt	78 Pcnt	82 Pcnt
1790638116	130 Pkt	78 Pcnt	83 Pcnt
1790637816	140 Pkt	78 Pcnt	83 Pcnt
1790637516	140 Pkt	78 Pcnt	84 Pcnt
1790637216	140 Pkt	78 Pcnt	85 Pcnt
1790636916	140 Pkt	78 Pcnt	86 Pcnt
1790636616	140 Pkt	78 Pcnt	86 Pcnt
1790636316	130 Pkt	78 Pcnt	87 Pcnt
1790636016	140 Pkt	78 Pcnt	86 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

EffTo: 0, 1, 0

Eff1: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)