APRS Track Direct

My position About ☰

reset

TA6BDL Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TA6BDL. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RxTraffic*	RSSI*	Voltage*
1758222576	28 Pkt	-64 dBm	0.04 V
1758221846	25 Pkt	-62 dBm	0.04 V
1758221116	30 Pkt	-63 dBm	0.04 V
1758220386	27 Pkt	-63 dBm	0.04 V
1758219656	25 Pkt	-63 dBm	0.04 V
1758218926	22 Pkt	-63 dBm	0.04 V
1758218196	19 Pkt	-63 dBm	0.04 V
1758217465	31 Pkt	-63 dBm	0.04 V
1758216736	26 Pkt	-63 dBm	0.04 V
1758216005	28 Pkt	-62 dBm	0.04 V
1758215275	18 Pkt	-63 dBm	0.04 V
1758214545	26 Pkt	-62 dBm	0.04 V
1758213815	33 Pkt	-62 dBm	0.04 V
1758213085	24 Pkt	-63 dBm	0.04 V
1758212355	19 Pkt	-63 dBm	0.04 V
1758211625	29 Pkt	-62 dBm	0.04 V
1758210895	22 Pkt	-63 dBm	0.04 V
1758210165	25 Pkt	-62 dBm	0.04 V
1758209436	29 Pkt	-63 dBm	0.04 V
1758208705	23 Pkt	-63 dBm	0.04 V
1758207975	36 Pkt	-63 dBm	0.04 V
1758207245	29 Pkt	-63 dBm	0.04 V
1758206515	33 Pkt	-63 dBm	0.04 V
1758205785	30 Pkt	-62 dBm	0.04 V
1758205055	30 Pkt	-62 dBm	0.04 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)