APRS Track Direct

My position About ☰

reset

BM3FFG-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BM3FFG-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1732291067	34.4 C	6 p	33 p	1066 p
1732289866	34.2 C	5 p	62 p	1066 p
1732288667	34.9 C	22 p	84 p	1065 p
1732287467	36 C	35 p	93 p	1050 p
1732286266	34.6 C	27 p	93 p	1026 p
1732285067	35 C	31 p	88 p	1007 p
1732283866	34.4 C	35 p	80 p	991 p
1732282667	34.6 C	22 p	55 p	965 p
1732281466	33.7 C	23 p	41 p	953 p
1732280267	34.6 C	10 p	23 p	939 p
1732279066	35.1 C	8 p	13 p	945 p
1732277867	34.6 C	5 p	6 p	941 p
1732276666	36 C	0 p	1 p	945 p
1732275467	34.3 C	1 p	2 p	951 p
1732274266	34.4 C	0 p	15 p	957 p
1732273067	34.6 C	1 p	36 p	967 p
1732271866	34.4 C	14 p	57 p	979 p
1732270667	34.9 C	21 p	59 p	979 p
1732269466	35.5 C	22 p	70 p	970 p
1732268267	35 C	16 p	64 p	958 p
1732267066	33.1 C	32 p	79 p	946 p
1732265867	33.6 C	16 p	67 p	945 p
1732264666	34.4 C	31 p	91 p	1011 p
1732263466	34.6 C	20 p	95 p	1001 p
1732262267	36 C	40 p	78 p	1033 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)