APRS Track Direct

My position About ☰

reset

TA4IB-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TA4IB-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	RxTraffic*	TxTraffic*	RSSI*	Voltage*
1790620423	28 Pkt	3 Pkt	-31 dBm	0.35 V
1790617695	30 Pkt	16 Pkt	-32 dBm	0.35 V
1790614959	12 Pkt	11 Pkt	-33 dBm	0.35 V
1790612226	0 Pkt	28 Pkt	-34 dBm	0.35 V
1790609481	0 Pkt	16 Pkt	-30 dBm	0.35 V
1790606743	0 Pkt	35 Pkt	-31 dBm	0.35 V
1790603996	0 Pkt	18 Pkt	-31 dBm	0.35 V
1790601259	0 Pkt	3 Pkt	-30 dBm	0.35 V
1790598532	0 Pkt	16 Pkt	-31 dBm	0.35 V
1790595795	0 Pkt	4 Pkt	-30 dBm	0.35 V
1790593068	0 Pkt	1 Pkt	-32 dBm	0.35 V
1790590343	0 Pkt	6 Pkt	-31 dBm	0.35 V
1790587614	0 Pkt	1 Pkt	-32 dBm	0.37 V
1790584889	29 Pkt	6 Pkt	-31 dBm	0.35 V
1790582160	41 Pkt	8 Pkt	-32 dBm	0.35 V
1790579426	31 Pkt	14 Pkt	-31 dBm	0.37 V
1790576689	30 Pkt	12 Pkt	-31 dBm	0.39 V
1790573956	3 Pkt	0 Pkt	-32 dBm	0.45 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)