APRS Track Direct

My position About ☰

reset

HS8AS-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS8AS-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TEMP*	HUM*	VBAT *
1782568310	26.78 °C	85.1 %RH	4.01 V
1782567710	26.94 °C	83.3 %RH	4.01 V
1782567110	27.08 °C	82.1 %RH	4.01 V
1782566510	27.41 °C	82.2 %RH	4.01 V
1782565910	27.75 °C	81.2 %RH	4.01 V
1782565310	27.88 °C	79.9 %RH	4.01 V
1782564710	28.17 °C	78.3 %RH	4.01 V
1782564110	28.41 °C	77.3 %RH	4.01 V
1782563510	28.32 °C	76.7 %RH	4.01 V
1782562910	28.7 °C	74 %RH	4.02 V
1782562310	29.37 °C	68.7 %RH	4 V
1782561689	29.46 °C	66.1 %RH	4.01 V
1782561089	29.21 °C	70.1 %RH	4.02 V
1782560489	29.28 °C	68 %RH	4.01 V
1782559889	29.49 °C	67.2 %RH	4.01 V
1782559289	29.86 °C	66.3 %RH	4.02 V
1782558689	29.96 °C	65.4 %RH	4.02 V
1782558089	30.37 °C	65.7 %RH	4.02 V
1782557489	30.38 °C	65 %RH	4.02 V
1782556888	30.44 °C	65 %RH	4.02 V
1782556288	30.99 °C	63.3 %RH	4.01 V
1782555689	31.25 °C	62.2 %RH	4.02 V
1782555088	31.51 °C	62.8 %RH	4.02 V
1782554490	31.55 °C	64.1 %RH	4.02 V
1782553888	32.04 °C	65.9 %RH	4.01 V

*Used Equation Coefficients:

TEMP: 0, 0.01, 0

HUM: 0, 0.1, 0

VBAT : 0, 0.01, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)