APRS Track Direct

My position About ☰

reset

YE1BPQ-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YE1BPQ-13. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	TxTraffic*	RSSI*	Voltage*
1732267704	0 Pkt	-76 dBm	13.8 V
1732266782	1 Pkt	-76 dBm	16.18 V
1732265859	3 Pkt	-75 dBm	16.45 V
1732264937	1 Pkt	-77 dBm	15.96 V
1732264015	0 Pkt	-76 dBm	11.44 V
1732263093	0 Pkt	-77 dBm	14.15 V
1732262171	0 Pkt	-76 dBm	14.36 V
1732261249	1 Pkt	-76 dBm	19.3 V
1732260327	1 Pkt	-77 dBm	18.29 V
1732259405	0 Pkt	-77 dBm	17.43 V
1732258483	0 Pkt	-78 dBm	19.46 V
1732257561	0 Pkt	-76 dBm	20.18 V
1732256639	1 Pkt	-78 dBm	20.06 V
1732255717	2 Pkt	-77 dBm	19.87 V
1732254795	2 Pkt	-75 dBm	20.73 V
1732253872	0 Pkt	-76 dBm	20.26 V
1732252950	0 Pkt	-75 dBm	19.56 V
1732252028	0 Pkt	-76 dBm	20.22 V
1732251107	0 Pkt	-75 dBm	20.2 V
1732250184	0 Pkt	-76 dBm	20.2 V
1732249262	0 Pkt	-76 dBm	20.24 V
1732248341	0 Pkt	-77 dBm	20 V
1732247419	0 Pkt	-76 dBm	19.63 V
1732246497	0 Pkt	-75 dBm	20.26 V
1732245575	0 Pkt	-77 dBm	20.08 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)