APRS Track Direct

My position About ☰

reset

YD8VAF-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YD8VAF-13. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1753848362	0 Pkt	-61 dBm	4.84 V
1753848040	0 Pkt	-61 dBm	4.59 V
1753847718	0 Pkt	-59 dBm	4.43 V
1753847396	0 Pkt	-60 dBm	4.27 V
1753847074	0 Pkt	-60 dBm	4.2 V
1753846752	0 Pkt	-61 dBm	3.96 V
1753846430	0 Pkt	-60 dBm	4.08 V
1753846108	0 Pkt	-60 dBm	4.22 V
1753845786	0 Pkt	-61 dBm	4.53 V
1753845464	0 Pkt	-61 dBm	4.29 V
1753845142	1 Pkt	-62 dBm	4.47 V
1753844820	0 Pkt	-60 dBm	4.29 V
1753844498	0 Pkt	-60 dBm	4.31 V
1753844176	0 Pkt	-59 dBm	4.47 V
1753843854	0 Pkt	-60 dBm	3.83 V
1753843532	0 Pkt	-60 dBm	3.53 V
1753843210	0 Pkt	-60 dBm	3.49 V
1753842888	0 Pkt	-60 dBm	3.47 V
1753842566	0 Pkt	-60 dBm	3.24 V
1753842244	0 Pkt	-59 dBm	2.3 V
1753841922	0 Pkt	-61 dBm	1.68 V
1753841600	0 Pkt	-60 dBm	2.54 V
1753841278	0 Pkt	-60 dBm	2.67 V
1753840956	0 Pkt	-59 dBm	3.32 V
1753840634	0 Pkt	-59 dBm	4.55 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)