APRS Track Direct

My position About ☰

reset

IT9FDP-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IT9FDP-15. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Value1*	Value2*	Value3*	Value4*	Value5*
1745051528	21.48	14.05	13.49	28.1	24.6
1745051227	21.6	14.08	13.51	28.1	24.6
1745050928	21.31	14.1	13.54	28.2	24.6
1745050628	21.71	14.09	13.53	28.1	24.5
1745050344	21.5	14.09	13.46	28.1	24.5
1745050028	21.07	14.09	13.46	28.1	24.5
1745049727	21.37	14.12	13.49	28	24.3
1745049427	21.37	14.06	13.55	28	24.3
1745049128	21.51	14.08	13.51	28	24.2
1745048827	21.48	14.08	13.54	27.9	24.1
1745048528	21.43	14.09	13.43	27.9	24.1
1745048228	21.32	14.1	13.48	27.9	24.1
1745047927	21.45	14.04	13.48	27.9	24
1745047628	21.53	14.1	13.49	27.8	24
1745047327	21.46	14.04	13.49	28	24
1745047027	21.49	14.09	13.49	28	24
1745046728	21.55	14.08	13.44	28.1	24
1745046427	21.52	14.09	13.51	28.2	24
1745046127	21.57	14.14	13.41	28.3	24.1
1745045827	21.49	14.05	13.49	28.3	24.1
1745045527	21.56	14.09	13.42	28.4	24.1
1745045227	21.57	14.09	13.48	28.6	24.1
1745044927	21.65	14.05	13.4	28.8	24.3
1745044627	21.66	14.06	13.42	29	24.4
1745044327	21.32	14.05	13.48	29.3	24.6

*Used Equation Coefficients:

Value1: 0, 1, 0

Value2: 0, 1, 0

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)