APRS Track Direct

My position About ☰

reset

TA2BXX-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TA2BXX-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1754056062	0 Pkt	-38 dBm	14.68 V
1754055748	1 Pkt	-38 dBm	14.79 V
1754055435	0 Pkt	-38 dBm	14.7 V
1754055122	0 Pkt	-38 dBm	14.77 V
1754054808	1 Pkt	-38 dBm	14.79 V
1754054495	0 Pkt	-37 dBm	14.79 V
1754054182	0 Pkt	-37 dBm	14.77 V
1754053868	1 Pkt	-37 dBm	14.77 V
1754053555	0 Pkt	-37 dBm	14.81 V
1754053241	1 Pkt	-38 dBm	14.77 V
1754052928	0 Pkt	-38 dBm	14.79 V
1754052615	0 Pkt	-37 dBm	14.68 V
1754052301	1 Pkt	-38 dBm	14.77 V
1754051988	0 Pkt	-37 dBm	14.7 V
1754051675	0 Pkt	-37 dBm	14.85 V
1754051361	0 Pkt	-37 dBm	14.77 V
1754051096	0 Pkt	-37 dBm	14.81 V
1754050783	0 Pkt	-38 dBm	14.77 V
1754050469	1 Pkt	-38 dBm	14.77 V
1754050156	0 Pkt	-39 dBm	14.77 V
1754049843	0 Pkt	-39 dBm	14.77 V
1754049529	1 Pkt	-37 dBm	14.77 V
1754049216	0 Pkt	-36 dBm	14.7 V
1754048903	0 Pkt	-39 dBm	14.77 V
1754048589	1 Pkt	-36 dBm	14.72 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)