APRS Track Direct

My position About ☰

reset

YB8VK-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YB8VK-13. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1749329339	0 Pkt	-85 dBm	0.51 V
1749329017	0 Pkt	-83 dBm	0.51 V
1749328695	1 Pkt	-83 dBm	0.62 V
1749328373	0 Pkt	-85 dBm	0.35 V
1749328051	0 Pkt	-83 dBm	0.88 V
1749327729	0 Pkt	-83 dBm	0.33 V
1749327407	0 Pkt	-83 dBm	0.08 V
1749327085	0 Pkt	-83 dBm	0.59 V
1749326763	0 Pkt	-84 dBm	0.1 V
1749326442	0 Pkt	-84 dBm	0.16 V
1749326120	0 Pkt	-85 dBm	0.31 V
1749325797	0 Pkt	-84 dBm	0.1 V
1749325476	0 Pkt	-84 dBm	0.64 V
1749325153	0 Pkt	-84 dBm	0.45 V
1749324832	0 Pkt	-84 dBm	0.37 V
1749324509	0 Pkt	-84 dBm	0.1 V
1749324187	0 Pkt	-83 dBm	0.62 V
1749323865	0 Pkt	-83 dBm	0.14 V
1749323544	0 Pkt	-83 dBm	0.08 V
1749323221	0 Pkt	-84 dBm	0.06 V
1749322899	0 Pkt	-84 dBm	0.41 V
1749322577	1 Pkt	-82 dBm	0.33 V
1749322256	0 Pkt	-83 dBm	0.49 V
1749321934	0 Pkt	-82 dBm	0.39 V
1749321612	1 Pkt	-83 dBm	0.35 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)