APRS Track Direct

My position About ☰

reset

YB8VJT-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YB8VJT-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1732270125	0 Pkt	-66 dBm	2.34 V
1732269803	0 Pkt	-67 dBm	2.34 V
1732269481	0 Pkt	-68 dBm	2.36 V
1732269159	0 Pkt	-66 dBm	2.4 V
1732268837	0 Pkt	-65 dBm	0.53 V
1732268515	0 Pkt	-65 dBm	0.57 V
1732268193	1 Pkt	-66 dBm	0.51 V
1732267871	0 Pkt	-66 dBm	0.53 V
1732267549	0 Pkt	-66 dBm	0.31 V
1732267227	0 Pkt	-64 dBm	0.35 V
1732266905	0 Pkt	-65 dBm	0.41 V
1732266583	0 Pkt	-66 dBm	0.59 V
1732266260	1 Pkt	-66 dBm	0.88 V
1732265938	0 Pkt	-65 dBm	1.78 V
1732265616	0 Pkt	-66 dBm	2.91 V
1732265294	3 Pkt	-67 dBm	1.83 V
1732264972	1 Pkt	-67 dBm	1.62 V
1732264650	0 Pkt	-65 dBm	3.4 V
1732264328	0 Pkt	-67 dBm	3.4 V
1732264006	0 Pkt	-68 dBm	2.71 V
1732263684	0 Pkt	-68 dBm	3.04 V
1732263362	0 Pkt	-67 dBm	2.38 V
1732263040	0 Pkt	-67 dBm	2.21 V
1732262718	0 Pkt	-67 dBm	2.26 V
1732262396	0 Pkt	-67 dBm	2.21 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)